Measurement and optimization of cutting forces, surface roughness and temperature in turning of AZ91 Mg alloy

dc.authorid0000-0002-4522-066X
dc.contributor.authorAkgün, Mahir
dc.date.accessioned2023-10-03T06:16:01Z
dc.date.available2023-10-03T06:16:01Z
dc.date.issued2023
dc.departmentTeknik Bilimler Meslek Yüksekokulu
dc.description.abstractThis study presents the experimental and statistical examination of machinability of AZ91 alloy, in terms of cutting forces (Fc, Ff, and Fp), surface roughness (Ra) and cutting temperature (T). In the first step, test samples have been produced using the casting method and the microstructures of these samples have been characterized by SEM and EDS. Secondly, the turning tests have been performed in CNC turning at three different cutting speeds (200, 300, and 400 m/min), three different feed rates (0.1, 0.2, and 0.3 mm/rev), and three different depths of cut (1, 1.5, and 2 mm). Thereafter, the turning simulations have been performed by Deform 3D software. Finally, experiment results were statistically analyzed using Taguchi, Anova, and regression analysis. The outcomes of this study show that the feed rate is the most significant parameter with 69.43, 90.04, 88.53, and 96.22% effect rates on the cutting force components (Fc, Ff, and Fp) and surface roughness (Ra) respectively, while the cutting speed is the most significant parameter with 70.83% effect rates on the cutting temperature. There is an average of 4.5% deviation between the experimental and simulation results of Fc. The results also stated that the microstructure of the samples consisted of ?-Mg phase and ?-intermetallic (Mg17Al12) phase, and the built-up edge (BUE) formation was the dominant wear mode for all the cutting tools.
dc.identifier.doi10.1007/s12046-023-02113-3
dc.identifier.issn0256-2499
dc.identifier.issue2en_US
dc.identifier.scopusqualityQ1
dc.identifier.urihttps:/dx.doi.org10.1007/s12046-023-02113-3
dc.identifier.urihttps://hdl.handle.net/20.500.12451/11044
dc.identifier.volume48en_US
dc.identifier.wosWOS:000963918000001
dc.identifier.wosqualityQ2
dc.indekslendigikaynakWeb of Science
dc.indekslendigikaynakScopus
dc.language.isoen
dc.relation.ispartofSadhana - Academy Proceedings in Engineering Sciences
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanı
dc.rightsinfo:eu-repo/semantics/embargoedAccess
dc.subjectAZ91 Mg Alloy
dc.subjectCutting Force
dc.subjectCtting Temperature
dc.subjectMachining
dc.subjectMicrostructure
dc.subjectOptimization
dc.subjectSurface Roughness
dc.titleMeasurement and optimization of cutting forces, surface roughness and temperature in turning of AZ91 Mg alloy
dc.typeArticle

Dosyalar

Orijinal paket
Listeleniyor 1 - 1 / 1
[ X ]
İsim:
akgun-mahir-2023.pdf
Boyut:
3.73 MB
Biçim:
Adobe Portable Document Format
Açıklama:
Tam Metin / Full Text
Lisans paketi
Listeleniyor 1 - 1 / 1
[ X ]
İsim:
license.txt
Boyut:
1.44 KB
Biçim:
Item-specific license agreed upon to submission
Açıklama: